為了確保設備的安全和穩定運行啟動時應

　　In order to ensure the safe and stable operation of the equipment, it should be started

　　1.開啟排氣閥 ：在啟動高壓羅茨鼓風機時，應慢慢開啟排氣閥直到全開，同時按住電控箱上的停止按鈕，以確保風機啟動時的安全。

　　1. Open the exhaust valve: When starting the high-pressure Roots blower, slowly open the exhaust valve until it is fully open, while holding down the stop button on the electrical control box to ensure safety during fan start-up.

　　2.皮帶張力和皮帶盤偏正 ：在啟動前，應檢查高壓羅茨鼓風機的皮帶張力和皮帶盤是否偏正，如有異常應及時聯系維修工人更換。

　　2. Belt tension and pulley misalignment: Before starting, check the belt tension and pulley misalignment of the high-pressure Roots blower. If there are any abnormalities, contact the maintenance worker for replacement in a timely manner.

　　3.儀表和電氣設備 ：在啟動前，應查驗儀表是否正常，包括壓力表開關是否處在常閉狀態，如有需要，打開壓力表開關進行測量。同時，確保電控箱上的鼓風機開關處于正確的檔位，并按下啟動按鈕。

　　3. Instruments and electrical equipment: Before starting, check whether the instruments are normal, including whether the pressure gauge switch is in a normally closed state. If necessary, open the pressure gauge switch for measurement. Meanwhile, ensure that the blower switch on the electrical control box is in the correct gear and press the start button.

　　4.風機出口閥和運轉情況 ：在啟動前，應認真檢查運轉的風機出口閥是否開啟，確保啟動的風機與具體運轉的風機一致，避免因誤操作導致設備損壞。

　　4. Fan outlet valve and operation: Before starting, carefully check whether the outlet valve of the running fan is open to ensure that the started fan is consistent with the specific running fan, and avoid equipment damage caused by misoperation.

　　5.載啟動和逐步加載 ：啟動后，嚴禁完全關閉出風道，以免造成爆炸事故。應先進行無負載運轉20分鐘，檢查是否有異常聲音和異常發熱，然后再逐步加載至額定壓力。

　　5. Loading and gradual loading: After starting, it is strictly prohibited to completely close the air outlet duct to avoid explosion accidents. It should be operated without load for 20 minutes first to check for any abnormal sounds or heating, and then gradually loaded to the rated pressure.

　　6.運轉中的異常情況 ：在風機正常運轉后，應慢慢關閉排氣閥，避免因瞬時電流過大而燒毀電機。同時，運行中應調節接觸氧化池的旁通閥，使之勻稱爆氣。

　　6. Abnormal situations during operation: After the fan is running normally, the exhaust valve should be slowly closed to avoid burning out the motor due to excessive instantaneous current. At the same time, the bypass valve of the contact oxidation tank should be adjusted during operation to ensure even gas explosion.

　　7.保養和維護 ：定期清理風機房，保持干凈和通風良好，定期維護滴油嘴的漏油情況和閘閥的靈活性，確保設備的長期穩定運行。

　　7. Maintenance and upkeep: Regularly clean the fan room to maintain cleanliness and good ventilation, regularly maintain the oil leakage of the drip nozzle and the flexibility of the gate valve to ensure the long-term stable operation of the equipment.

　　8.檢查和巡檢 ：在啟動和運行過程中，應定期檢查安全閥、逆止閥、管道出氣閥等安全設施的工作狀態，確保設備無異常聲響、振動和漏氣現象。同時，檢查油位和油質，確保潤滑油符合要求。

　　8. Inspection and patrol: During the start-up and operation process, the working status of safety facilities such as safety valves, check valves, and pipeline exhaust valves should be regularly checked to ensure that the equipment has no abnormal noise, vibration, or air leakage. At the same time, check the oil level and quality to ensure that the lubricating oil meets the requirements.

　　9.超壓和過載 ：在運行過程中，應對風機的壓力進行檢查，避免超壓情況的發生，并在滿載時避免突然停車，以免造成設備損壞或安全事故。

　　9. Overpressure and Overload: During operation, the pressure of the fan should be checked to avoid overpressure situations, and sudden stopping at full load should be avoided to prevent equipment damage or safety accidents.

　　10.音和振動 ：在運行過程中，應密切觀察設備的噪音和振動情況，如有異常應立即停機檢查并排除故障。

　　10. Sound and vibration: During operation, the noise and vibration of the equipment should be closely observed. If there are any abnormalities, the machine should be stopped immediately for inspection and troubleshooting.

　　通過以上注意事項，可以有效降低高壓羅茨鼓風機運行過程中的安全風險，確保設備的穩定運行和操作人員的安全。

　　By following the above precautions, the safety risks during the operation of the high-pressure Roots blower can be effectively reduced, ensuring the stable operation of the equipment and the safety of the operators.

　　本文由 高壓羅茨鼓風機進行編寫，想要了解更多的產品及更詳細的精彩內容，請關注我們的網站：http://www.4wpk.cn。

　　This article is written by a high-pressure Roots blower. If you want to learn more about our products and more detailed exciting content, please follow our website: http://www.4wpk.cn .